Master-force 252-8036 Operator's Manual

www.wackergroup.comOperator´s ManualVIBRATORY PLATEBPU 3545A0200301en - 12.20010008783 100

TD00575GB8TECHNICAL DATABPU 3545AItem no. 0008783 ...Operating weightwithout extension plates (440) kg: 294with extension plates narrow (500) kg: 308

T00803GB9DESCRIPTIONField of applicationThe application range of these machines reaches from the trench and surface compaction, even with semi-cohesiv

T00803GB10DESCRIPTIONDescription of functionThe vibration required for compaction is produced by the exciter (4) which is firmly joinded to the lower

T00804GB11TRANSPORT TO WORK SITE / RECOMMENDATIONS ON COMPACTIONTransport to work siteConditions:- To transport the vibration plate, use only suitable

T00805GB12OPERATIONStartingPre-starting check1. Oil level checkInsert dipstick in oil filler neck, but without screwing in. If oil level is low, fill

T00805GB13

T00805GB14OPERATIONHandlingAs the engine warms up, gradually move the choke lever to the OPEN position.Position the throttle lever for the desired eng

T00806GB15MAINTENANCEMaintenance scheduleCheck all external screw connections for tight fit approx. 8 hours after first operation.Parts Maintenance jo

T00806GB16MAINTENANCEEngine oilOil changeDrain the oil while the engine is still warm to assure rapid and complete draining.1. Remove the oil filler c

T00806GB17MAINTENANCESpark plugSpark plug serviceRecommended spark plug: BP6ES-11, BPR6ES-11 (NGK), W20EP-U11, W20EPR-U11 (ND).Caution: Never use a sp

85716 Unterschleißheim Tel. 089/3 10 60 31 Fax 089/3 17 13 0786167 Augsburg Tel. 0821/70 22 07 Fax 0821/70 78 5893128 Regenstauf Tel. 09402/78 20 10 F

T00806GB18MAINTENANCEService instructions1. Adjusting the V-belt tensionRemove belt guard. Loosen nuts situated on the motor V-belt pulley and remove

T00806GB19MAINTENANCE3. Bleeding hydraulic control:1. Remove apron (17) by undoing the screws (16).2. Move centre pole into vertical position, move co

T00743GB20MOTORHigh altitude applicationsAir is rarer at greater altitudes and the main jet of the standard carburettor supplies the engine with anext

T00386GB21FAULTSForward speed too lowCause: - Too little hydraulic oil in the centre pole head.- Air in hydraulic control.Remedy: - Top up hydraulic o

T00807GB22ACCESSORIESAccessories Part No.Set of blanking bolts for use without extension plates 0067519Set of extension plates narrow (500 wide) 0126

C0007907.GBEC - CONFORMITY-CERTIFICATEWacker-Werke GmbH & Co. KG , Preußenstraße 41, 80809 Münchenhereby certify that the construction equipment s

24

File certificate carefullyDIN EN ISO 9001 Certificate

A-1110 Wien Tel. 0043(01) 767 15 15 Fax (1) 7 67 15 15 34/356122 Fritzens Tel. (05224) 5 13 51 Fax (05224) 51 35 148054 Graz-Straßgang Tel. (0316) 28

H00575GB1CONTENTSType Item no.BPU 3545A 0008783 ...This machine has been equipped with an EPA certified engine.Additional information can be found in

AUS-Springvale, Vic. 3171 Tel. 0061(03) 9547-4033 Fax (03) 9562-3371Norwood, S.A. 5067 Tel. (08) 8362-2331 Fax (08) 8362-8469Woodridge, Qld. 4114 Tel.

2

T00778GB3FOREWORDForewordFor your own safety and protection from bodily injuries, carefully read, understand and follow the safety instruc-tions in th

0126424GBIVZ.GB.fm4TABLE OF CONTENTSFOREWORD 3SAFETY INSTRUCTIONS 6General instructions 6Operation 6Safety checks 7Maintenance 7Transport 7Maintenance

0126424GBIVZ.GB.fm5TABLE OF CONTENTSForward speed too low 21Reverse speed too low 21No reverse motion 21Loss of hydraulic oil 21Engine does not start

SV00019GB6SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS FOR THE USE OF VIBRATORYPLATES WITH COMBUSTION ENGINESGeneral instructions1. Vibratory plates may onl

SV00019GB7SAFETY INSTRUCTIONS12. Make sure the soil or subsoil to be compacted has a high enough load carrying capacity.13. Use appropriate protective